Newsletter
Elite
Elite back
Elite logo
Power Redundancy
Stabilization Systems
Telemetry
Jeti USA
Jeti back
jeti logo
Transmitters
Receivers
Telemetry
Axi Motors
axi back
axi logo
V2 Brushless
Sailplane
CycloneAccessories
Axi Motors
secraft back
secraft logo
Tx/Rx Accessories
Securing Systems
Fuel Systems
TopmodelCZ
topmodel back
topmodel back
TD/E-Sailplanes
Scale Sailplanes
E-Hotliners
Opale
opale back
opale logo
Paragliders
Paramotors
Wings & Pilots

Elite EX5 K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)


Price: $115.00
In Stock: 3
Part: ESELITE-EX5-K
Back In Stock Notification
Made In Czech Republic
Elite EX5-K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)Elite EX5-K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)

Elite EX5-K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)
The Dual Input Servo Channel Expander EX5 is an intelligent bus manager compatible with several radio control systems. The device converts serial bus signal from up to two receivers to either standard PWM servo outputs, or configurable bus outputs. It offers up to five configurable and high-power servo ports with optional period and fail-safe setting.

The EX5 is a perfect choice for models with complex wing or tail mechanics where multiple servos may be connected to a primary receiver/receivers using just a single cable. In addition, if you are running out of receiver channels simply connect additional SE2/SE4/SE6 to the EX5 serial line/s and freely assign any channels.

The EX5 offers flight stabilization (Optional) using the integrated MEMS gyroscope/accelerometer. Up to three configurable flight modes can be used, each with different stabilization gains and settings. In connection with other devices from our production, such as SE4 or SE6, you can create a complex installation with just a few signal/power cables.

Specifications and Features
- Supported Protocols: Jeti EX, Multiplex M-LINK, Graupner HoTT, Futaba S.Bus/S.Bus2
- Small dimensions and high current throughput via the integrated MR30 power connectors.
- Telemetry (RC system dependent): Temperature, Voltage, G-Force (+/-30G), Attitude (Roll/Pitch/Yaw).
- Gyro-stabilized servo outputs, EX Bus, SRXL16ch. or S.Bus.
- Flight stabilization offering 3 configurable flight modes (Manual/Acro/Horizon).
- Automatic detection of serial data/telemetry after startup.
- Configuration through the transmitter or external terminal (JETIBOX/SMART-BOX).
- Firmware updates via USB interface.

Elite EX5 Serial Bus Dual Input Channel Expander w/G-Force, Temperature Sensors & Stabilization (Optional)Elite EX5 Serial Bus Dual Input Channel Expander w/G-Force, Temperature Sensors & Stabilization (Optional)Elite EX5 Serial Bus Dual Input Channel Expander w/G-Force, Temperature Sensors & Stabilization (Optional)

Advance Model Installation
Attach the required servos or additional bus devices (SE2/SE4/SE6) to the EX5 (ports 1-5). Connect up to two receivers through their bus outputs. In case of a single receiver, always connect primary RX to the RX1 port of the EX5. Turn on the transmitter and apply the appropriate power source to the EX5. The status LED starts blinking as soon as the EX5 detects signal on the serial line. Please note that both receivers have to use the same data protocol (S.Bus, EX Bus...).

Elite EX5 Serial Bus Dual Input Channel Expander w/G-Force, Temperature Sensors & Stabilization (Optional)

Elite EX5 Serial Bus Dual Input Channel Expander w/G-Force, Temperature Sensors & Stabilization (Optional)

Flight Stabilization (Up to 16 Channels)
Install the EX5 in parallel to the flight axes, as close to the center of gravity as possible. By default, the axes printed on the device point in the direction of flight: X-Front, Y-Right, Z-Top. In case you need to install the EX5 in a different direction, please keep in mind that the arrows on the device must be parallel to the flight axes. In such case, the resulting orientation of the device must be set in the configuration menu.

Elite EX5-K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)Elite EX5-K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)
Stabilization Modes and Channel SwitchYou can use up to three flight stabilization modes operated by a dedicated transmitter channel.
  • Manual - Flight stabilization is disabled and the EX5 just passes channel data from the receiver(s).
  • Acro- Standard flight stabilization with configurable rate/heading gains. You can decide which axes will be controlled by just rate gains (so called Normal or Damping mode) with heading gain disabled. With additional heading gains, the Heading hold function will be active.
  • Horizon- The stabilization function is similar to the Acro mode, additionally the model returns to horizontal position if the Aileron/Elevator sticks are released.
Stabilization GainsThe stabilization gains can be set independently for each axis and each flight mode. There are six parameters in total and in the configuration menu you edit the value for the currently active flight mode.

More information (links):
* Instruction Manual (pdf.)
* Click Here for Firmware Updates & MAV Manager

Continues/Peak Current: 15A/60A (2 Seconds)
Operational Current: 15mA
Operational Voltage: 4-14V (Recommended 5-8.4V)
Dimensions: 38mm x 26mm x 12mm
Weight: 14g




Elite EX5-K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)
Elite EX5-K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)
Elite EX5-K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)

Elite EX5-K Serial Bus & Servo Channel Expander w/G-Force, Temperature, Stabilization (Jeti EX Bus, HoTT, S.Bus2 Expander)
 

Related Products:

MR30-M Connector Flat 2mm/20A 3-Pole w/Cover (2 Pair)
Price: $3.00    In Stock: 30
MR30-M Connector Flat 2mm/20A 3-Pole w/Cover (2 Pair)

Product Reviews:

(0 Ratings, 0 Reviews)